产品描述：

本产品是由无机胶凝材料、精细骨料及优质外加剂混合而成。和易性好，粘结力强，收缩率低，具有良好的施工性；优良的保水性，在干燥砌块基面上都能保证砂浆有效粘结；加水即用，质量稳定，施工方便，低耗、质轻。

 

产品特点：

优异的保水率；

和易性好，粘结力强；

加水即用，强度高。

 

用法用量：

1、 基材表面处理：基材表面应该洁净牢固，清除灰尘、油脂及颗粒等一切影响粘结性能的松软物。

2、 拌合：按照25kg干粉兑5L水的比例进行混合。调好的浆料宜在3小时内用完。

3、 施工：将搅拌均匀的砌筑砂浆用抹刀或者刮勺涂抹在加气混凝土砖粘结面，建议双面涂抹粘结浆料，每次涂抹厚度 2~3mm。加气砖安装时应对准缝隙，并充分挤压，使砖缝内的浆料饱满密实。砖缝宽度通常为3~4mm左右。

4、 用油灰刀及时清除缝隙处溢出的粘结剂浆料。

 

注意事项：

施工温度应在5-35℃之间。施工完毕后及时用清水冲洗，不慎入眼，应用大量清水冲洗，并及时就医。

 

执行标准：

JCT890-2017

 

储存运输：

本品须存放于室内5℃-35℃，防止冰冻、曝晒。保质期为6个月。

 

包装：

25KG/袋

 

温馨提示：

任何大面积施工前，都必须先做小面积适用性测试，任何因小面积测试可见的风险而没有规避带来的损失，我司概不负责，在产品应用方面的问题可咨询相应的技术人员。

 

 

 

 

 

 

 

 

 

 

 

 

 

HENRY100 Masonry Mortar

Product description:

This product is made of inorganic cementitious material, fine aggregate and high quality admixture. Good workability, strong adhesion, low shrinkage, with good application. Excellent water retention, the mortar can be effectively bonded on the dry base. After adding water can be used, stable quality, easy to apply, low consumption, light quality.

Features:

Excellent water retention;

Good workability and strong adhesion;

High compressive strength.

Application:

1. Surface treatment: the surface should be clean and firm, remove dust, grease, particles and all other things that affect the bond performance.

2. Mixing: mix 25kg powder to 5L water.The mortar should be used up within 3 hours.

3. Application: apply the masonry mortar with a spatula on the bonding surface of the aerated concrete plate. It is recommended to apply bonding mortar on both sides, with a thickness of 2~3mm each time. Plate installation should be aligned with the gap, and full extrusion, so that the gap in the slurry full and dense.The gap width is usually about 3~4mm.

4. With putty knife to clear the mortar in the gap.

Notes:

The construction temperature should be between 5-35℃.After completion of construction, flush with clean water immediately. In case of contact with eyes, rinse with plenty of water and seek medical advice.

Executive standard:

JCT890-2017.

Storage and transportation:

This product must be stored indoors at 5℃-35℃ to prevent freezing and insolation.Shelf life is 6 months.

Packing:

25kg/bag

Tips:

A small area suitability test must be performed before any large area application. Our company is not responsible for any loss caused by the visible risk of small area test without avoiding, and you can consult the corresponding technical personnel for the problem of product application.